IOutputDevice.write

write() writes up to count bytes from the buffer pointed buf to the file referred to by the file descriptor fd.

The number of bytes written may be less than count if, for example, there is insufficient space on the underlying physical medium, or the RLIMIT_FSIZE resource limit is encountered (see setrlimit(2)), or the call was interrupted by a signal handler after having written less than count bytes. (See also pipe(7).)

For a seekable file (i.e., one to which lseek(2) may be applied, for example, a regular file) writing takes place at the current file offset, and the file offset is incremented by the number of bytes actually writ‐ ten. If the file was open(2)ed with O_APPEND, the file offset is first set to the end of the file before writing. The adjustment of the file offset and the write operation are performed as an atomic step.

POSIX requires that a read(2) which can be proved to occur after a write() has returned returns the new data. Note that not all file sys‐ tems are POSIX conforming.

interface IOutputDevice
write
(
const(void)[] dst
)

Return Value

Type: ssize_t

On success, the number of bytes written is returned (zero indicates nothing was written). On error, -1 is returned, and errno is set appropriately.

If count is zero and fd refers to a regular file, then write() may return a failure status if one of the errors below is detected. If no errors are detected, 0 will be returned without causing any other effect. If count is zero and fd refers to a file other than a regu‐ lar file, the results are not specified.

write() writes up to count bytes from the buffer pointed buf to the file referred to by the file descriptor fd.

The number of bytes written may be less than count if, for example, there is insufficient space on the underlying physical medium, or the RLIMIT_FSIZE resource limit is encountered (see setrlimit(2)), or the call was interrupted by a signal handler after having written less than count bytes. (See also pipe(7).)

For a seekable file (i.e., one to which lseek(2) may be applied, for example, a regular file) writing takes place at the current file offset, and the file offset is incremented by the number of bytes actually written. If the file was open(2)ed with O_APPEND, the file offset is first set to the end of the file before writing. The adjustment of the file offset and the write operation are performed as an atomic step.

POSIX requires that a read(2) which can be proved to occur after a write() has returned returns the new data. Note that not all file systems are POSIX conforming.

Errors: EAGAIN The file descriptor fd refers to a file other than a socket and has been marked nonblocking (O_NONBLOCK), and the write would block.

EAGAIN or EWOULDBLOCK The file descriptor fd refers to a socket and has been marked nonblocking (O_NONBLOCK), and the write would block. POSIX.1-2001 allows either error to be returned for this case, and does not require these constants to have the same value, so a portable application should check for both possi‐ bilities.

EBADF fd is not a valid file descriptor or is not open for writing.

EDESTADDRREQ fd refers to a datagram socket for which a peer address has not been set using connect(2).

EFAULT buf is outside your accessible address space.

EFBIG An attempt was made to write a file that exceeds the imple‐ mentation-defined maximum file size or the process's file size limit, or to write at a position past the maximum allowed offset.

EINTR The call was interrupted by a signal before any data was written; see signal(7).

EINVAL fd is attached to an object which is unsuitable for writing; or the file was opened with the O_DIRECT flag, and either the address specified in buf, the value specified in count, or the current file offset is not suitably aligned.

EIO A low-level I/O error occurred while modifying the inode.

ENOSPC The device containing the file referred to by fd has no room for the data.

EPIPE fd is connected to a pipe or socket whose reading end is closed. When this happens the writing process will also receive a SIGPIPE signal. (Thus, the write return value is seen only if the program catches, blocks or ignores this sig‐ nal.)

Other errors may occur, depending on the object connected to fd.

Meta